Hp printer stuck on initializing.

a. Unplugged the power cable from the printer and wall outlet for 60 seconds. b. Reconnected the power cable to the printer and wall outlet. c. Issue remains. 2. Performed a power drain. a. Disconnected the power cord from the back of the printer, power button pressed for 30 seconds with the switch in ON position for 30 seconds.My printer is stuck on initializing with the hp logo on it. I have done the hard reboot and discharged charges by pulling the plug and holding on the power button for 30sec but still no success. I have also tried updating firmware but there isn't any communication with the printer after changing various ports. kindly assist.Reset the printer. With the printer turned on, disconnect the power cord from the rear of the printer. Wait at least 60 seconds. Reconnect the power cord to the rear of the printer. Turn ON the printer, if it does not automatically turn on. Wait until the printer is idle and silent before you proceed.04-15-2023 12:48 AM. If the printer does not come to ready, I suggest you power off and try restarting. It is possible that something has been shaken loose in shipping. If it does not startup properly after a power off, I would advise you to contact the vendor you bought it from and tell them you have a DOA product and ask them to replace it.

04-15-2023 12:48 AM. If the printer does not come to ready, I suggest you power off and try restarting. It is possible that something has been shaken loose in shipping. If it does not startup properly after a power off, I would advise you to contact the vendor you bought it from and tell them you have a DOA product and ask them to replace it.1) Take out the cartridges. 2) Unplug the power cord from the printer & wall. 3) Press and hold the power button down for 15 seconds and release the power button, wait for about 30 seconds. 4) Plug the power cord back into the printer and wall, ensure the printer is plugged into the wall & not into a surge protector.03-22-2022 04:41 PM. Product: HP Laser MFP 137fnw. Operating System: macOS 12.0 Monterey. HP Laser MFP 137fnw stuck at initializing and never completes initializing. After power on, I can hear the mechanical operation, then the printer goes into initializing phase but it never completes. I have successfully completed a power down and power ...

HP Color Laser Jet Pro MFP M477fnw stuck on initializing for hours. This printer is only a few years old. Our power went out and when I turn it on, it hangs at initializing for hours and hours. I've tried multiple quick fixes online, like hard resets, holding 3 buttons on the touch screen to reset it, but it still won't get passed initializing.

5. Close and Lock the Carriage latch close the top cover and switch ON the printer. 6. Printer should initialize and display a message to insert printheads as shown in the image below: 7. Select Options under printhead menu and select replace printhead. 8. Open the Top cover and Disengage the Carriage latch. 9.Create an account on the HP Community to personalize your profile and ask a question Your account also allows you to connect with HP support faster, access a personal dashboard to manage all of your devices in one place, view warranty information, case status and more.For assistance with first-time printer setup, click here. Reset the printer. With the printer turned on, disconnect the power cord from the rear of the printer. Wait at least 60 seconds. Reconnect the power cord to the rear of the printer. Turn ON the printer, if it does not automatically turn on. Wait until the printer is idle and silent ...05-09-2022 06:15 PM. Product: HP LaserJet Pro M1212nf Multifunction Printer. Operating System: Microsoft Windows XP. My m1212nf mfp is stuck in initializing limbo. I can print from the computer but I can't scan, copy or send/receive faxes. There are a few important faxes stuck in the cache that I would like to retrieve before turfing this machine.

11-27-2022 05:20 AM. Product: HP Color LaserJet Pro MFP M283fdw. Hello. My printer is stuck on initializing when i look under the network status. I have done a hard reset, i have removed the cartridges, removed power cord for over a minute. Switched back on refit still stuck. I have tried wireless & wired still the same.

My HP M1005 MFP Printer showing initializing only. so please help me to solve this issue Best Regards Dasharath Nishad - 7500210

HP Color Laser Jet Pro MFP M477fnw stuck on initializing for hours. This printer is only a few years old. Our power went out and when I turn it on, it hangs at initializing for hours and hours. I've tried multiple quick fixes online, like hard resets, holding 3 buttons on the touch screen to reset it, but it still won't get passed initializing.HP Support Agent. 07-23-2020 07:02 AM. Let's try a power reset on the printer. Reset the product. With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 60 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer.20,478 2,176 1,611. HP Support Agent. 02-23-2022 04:36 AM. Hi @ PatCCat, Welcome to the HP Support Community. I'd like to help! I understand the printer is stuck on initializing screen. We can perform a factory defaults on the printer to resolve the issue. The reset instructions are specific for your printer and performing those steps on a ...Get help with Large Format Printers, with direct access to all Large Format Knowledge Center· Ask anything · Find anything · Share anything at HP LKC It has been a while since anyone has replied. Simply ask a new question if you would like to start the discussion again .Jan 30, 2023 · Hp color laserjet enterprise m652 Stuck on initializing. 1 -Power cycled - removed power from back, removed ethernet cable, let sit for 10 seconds, pressed the power button in for 10 seconds the plugged directly into wall . 2- Cold reset - held down the X on startup and performed the cold reset under startup options Nov 11, 2015 · Please go through the steps in this document to make sure everything setup properly. Here is the link: Setting Up the Printer Hardware for HP Color LaserJet Pro M177fw MFP Printers. You can manually move the carousel for the toners, if it is stuck. Open the scanner lid and the lid below that so you should see the toners. Product: M452DN. Operating System: Microsoft Windows 10 (64-bit) HP LaserJet Pro M452 stuck on initializing right out of the box. Tags: M452dn. Microsoft Windows 10 (64-bit) View All (2) This topic has been archived. Information and links in this thread may no longer be available or relevant.

My printer is stuck on initializing. After startup it makes some noise then goes quiet. The whole time the circle keeps spinning but all it says is initializing. I have tried to both hard and soft reset it, unplug everything and reset, I have tried to replace the ink cartridges with new one and noth...Product: Laserjet pro mfp m225dw. Operating System: Microsoft Windows 10 (64-bit) After a reboot, my printer is stuck in the initializing screen. The first time this issue happened it took days to resolve on its own. This time it has been days and it is still not working. I've tried rebooting it.Hello there, Our Color Laserjet Pro MFP M176n is stuck at initializing since the last time the yellow toner cartridge has been replaced. After the replacement of the cartridge, the toner carousel turned, started making loud clicking noises and then stopped. It does this after every startup. It see...Feb 26, 2020 · HP LaserJet M1212nf MFP has been stuck at Initializing screen. I have tried some troubleshooting suggestion through the forums but still not working. I have done: Disconnected the power cable from the printer while the printer is still ON. Disconnected any other cables if connected the printer. Press and hold the printer’s power button for 15 ... If you have a question create a new topic by clicking here and select the appropriate board. Frank3211. 3 0 0. 128. New member. 10-25-2018 06:34 AM. Product: Laserjet Pro MFP M475DW. Operating System: Microsoft Windows 10 (64-bit)

Hello there, Our Color Laserjet Pro MFP M176n is stuck at initializing since the last time the yellow toner cartridge has been replaced. After the replacement of the cartridge, the toner carousel turned, started making loud clicking noises and then stopped.This is what I have tried: -unplugging the printer for various amounts of time, for up to 5 minutes before plugging in again. -held down the power button while plugging it in. -using HP print and scan doctor, it fails to communicate with …

Product: Samsung ProXpress SL-M4075FR Laser Multifunction Printer. when i turn on the printer it gets stuck at initializing stays there for about 30 mins, after it gets though that phase printer starts and runs normally. Already tried updating the firmware to the latest version, problem is still there. PS: From time to time it also gets stuck ...Hi, last night I went to the Hp support website and downloaded the update firmware file listed for the hp LaserJet pro MFP m281fdw printer. Then it - 8518468Learn how to fix firmware update issues on HP LaserJet printers when the control panel is stuck on an error screen. Chapters:00:00 Introduction00:19 Connect ...I have a M210dw printer in which will not pull an IP address as the TCP/IP v4 status (wired) constantly sits at 'initializing'. It may randomly initialize and pull the assigned IP, but as soon as it goes to sleep or is rebooted, it sticks back to 'initializing'. I saw one answer that says to reset the NVRAM [on similar models] but i cannot find ...Next, power OFF the printer, remove any/all toner/drum cartridges and power ON the printer. See what message (s) it gets. If it's still stuck on Initializing, you may need to reset the NVRAM or maybe even replace the formatter. If it shows to install/replace the toner/drum cartridge, begin replacing the item requested and closing the access door.If it does and attached to the network, you probably have a bad print job trying to print and causing the printer to crash and start again. 02-09-2015 08:27 PM. Thanks. But no cable is attached with printer expect Power cable. And networking is not enabled in this printer. There is no other way to configure or reset.Press and hold down CANCEL and > (right arrow button) at the same time while powering on printer. c. Continue to hold down buttons until the control panel display reads PERMANENT STORAGE INIT. d.Release the buttons. Printer will return to Ready automatically.Resetting the printer to its factory defaults may resolve this issue. The reset instructions are specific for your printer and performing those steps on a different printer may corrupt the device. I've sent you a private message with reset instructions, follow the reset instruction to perform a full reset and re-initialize the printer.

HP Support Agent. 07-23-2020 07:02 AM. Let's try a power reset on the printer. Reset the product. With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 60 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer.

Turn off the printer, unplug the power cord, and wait for about 60 seconds. Plug the power cord back in and turn on the printer. Check if the issue persists. Update Firmware: Make sure your printer's firmware is up-to-date. Visit the HP Support website, enter your printer model, and download the latest firmware if available.

Feb 11, 2020 ... How to do Hard Reset Hp OfficeJet Pro 8610 to fix the Failed Ink System Error . This usually will fix the printer or will tell you what is ...Hello, I am hoping someone can help me out. I have been working on this printer for a while and cannot get past the initializing screen. The screen will get stuck between 3% to 89%. I took out all the paper, ink cartages and printer heads. I did all sorts of re booting by unplugging and waiting 60 seconds. To unplugging and holding the power ...01-18-2017 10:32 AM. In my case I unplugged the machine and disconnected the 3 scanner connectors and then powered on. It didn't start up, but after removing power and plugging the scanner connectors back in and powering the machine up I was able to get it to the ready state. I updated the firmware and cycled power without an issue.Jul 1, 2022 ... I need help, hp laserjet 3055 stuck on after 6 arrow on hewlett pack problem. 11:44. Go to channel · HP Printer initializing Problem | HP laser ...Upon start up, as soon as the screen shows the HP logo (at this point, in black and white), press and hold, in the touch screen area only, the area just above the question mark, until the "...init" prompt appears, then release. This reset procedure will reboot the printer and take it back to READY state. larreaza. 6 0 0.If on wired network : Unplug the Ethernet cable from back of the printer. If on wireless network : Power of the Wireless router. Turn off the printer. Wait for 30 seconds. Turn on the printer. If the printer is in READY state, on the printer front panel, go to Setup -> Network Setup -> Network Services -> IPv6 -> Off.Product: Laserjet pro mfp m225dw. Operating System: Microsoft Windows 10 (64-bit) After a reboot, my printer is stuck in the initializing screen. The first time this issue happened it took days to resolve on its own. This time it has been days and it is still not working. I've tried rebooting it.If it does and attached to the network, you probably have a bad print job trying to print and causing the printer to crash and start again. 02-09-2015 08:27 PM. Thanks. But no cable is attached with printer expect Power cable. And networking is not enabled in this printer. There is no other way to configure or reset.Granted, there's not a lot to see in this initial video, but the responsiveness looks good and the onscreen keyboard is quite fetching. We know that not all that many people actual...Dec 12, 2012 · The HP Community is where owners of HP products, like you, volunteer to help each other find solutions. Create an account on the HP Community to personalize your profile and ask a question Your account also allows you to connect with HP support faster, access a personal dashboard to manage all of your devices in one place, view warranty ...

6,370. New member. 09-07-2021 04:31 AM. Product: M507dn. Operating System: Microsoft Windows 10 (64-bit) My M507 came out of sleep mode last night to print and went to a screen saying initalizing with a number counting up. I left it in the over night and it's still counting up.05-20-2023 12:49 PM. Product: HP ENVY Photo 7855 All-in-One Printer. Hi, I have an HP Envy 7855, and like others, have tried all of the suggested and/or recommended troubleshooting steps. I use this printer for work & am not in a position to purchase another one.Dec 31, 2019 ... hp #hp1005 #printer #printerrepair #fixprinterproblem मित्रों वीडियोअच्छा लगा हो तो लाइक करें चैनल को सब्सक्राइब करें अपने दोस्तों ...Instagram:https://instagram. maurices easy payravin r5xfigs scrubs sizingrasberry animal clinic 996. Level 1. 12-14-2020 10:30 AM. Product: mfp 127. Operating System: Microsoft Windows 10 (64-bit) not a new printer works great until yesterday will not complete initialzing and therefore will not print. Not able to access the set up simply. Tags: MFP 127.Jun 30, 2016 · Product: Laserjet Pro MFP M225dw. Operating System: Microsoft Windows 10 (64-bit) Read message board and tried the following steps. 1. Performed a hard reset. a. Unplugged the power cable from the printer and wall outlet for 60 seconds. b. Reconnected the power cable to the printer and wall outlet. ritchie brothers nashvilleairbnb pine az Aug 11, 2020 · 4 0 1. Level 1. 08-12-2020 02:51 PM. Well found the problem, connector J606 on the DC Controller, the ribbon cable was kinked. This caused the unit not to produce a engine test and caused the unit to stay in initializing. Thanks for your input Valsimot. Tags: HP LaserJet Enterprise MFP M632h. Jul 24, 2020 · HP Support Agent. 07-23-2020 07:02 AM. Let's try a power reset on the printer. Reset the product. With the printer turned on, disconnect the power cord from the rear of the printer. Unplug the power cord from the wall outlet. Wait at least 60 seconds. Plug the power cord back into the wall outlet. Reconnect the power cord to the printer. bmv appointment ohio 07-14-2020 04:54 AM. @Jonathan35, Welcome to HP Support Community! The only option left is to perform a full reset and re-initialize the printer. The reset instructions are specific for your printer and performing those steps on a different printer may brick the device. I've sent you a private message with reset instructions, follow the reset ...Yes No. 07-14-2014 06:30 PM. I realize this is an old thread, but I have just joined the greatly disappointed HP customers experiencing this operational problem with the M1217, and sick to my stomach at HP's response. I bought this printer less than one year ago, almost 11 months ago now.The HP Community is where owners of HP products, like you, volunteer to help each other find solutions. Create an account on the HP Community to personalize your profile and ask a question Your account also allows you to connect with HP support faster, access a personal dashboard to manage all of your devices in one place, view warranty ...